advanced work · University Blvd / Arlington Road corridor, Arlington, Jacksonville, FL 32211

Add roof-to-wall hurricane straps in a home's attic, University Blvd / Arlington Road corridor

Homes built on this block before modern wind codes often have no metal connector tying the roof trusses to the wall top plate -- just toe-nails. That is the single upgrade IBHS credits most for keeping the roof attached in a named storm. Standard: IBHS FORTIFIED Home (TM) -- Roof/Silver/Gold wind-mitigation construction standard for hurricane-prone housing (roof-to-wall connections, opening protection, soffit/vent hardening, garage-door bracing). SDG 11.b resilient housing. Proof: permit + connector spec sheet + before/after attic photos per truss bay + inspection pass + GPS Method (IBHS FORTIFIED Home (TM) -- Roof/Silver/Gold wind-mitigation construction standard for hurricane-prone housing (roof-to-wall connections, opening protection, soffit/vent hardening, garage-door bracing). SDG 11.b resilient housing.): 1. 1. Verify the permit and connector spec against the home's truss/rafter framing; photograph unconnected truss-to-wall bays from the attic hatch. 2. 2. Confirm rated uplift capacity of the chosen connector against the home's wind-exposure category. 3. 3. Install the metal connector at each truss-to-wall bay per manufacturer nailing/fastener pattern, working from the attic decking/joists. 4. 4. Photograph the installed strap and fastener pattern per bay from the same vantage as the before photos. 5. 5. Pass the framing inspection and record the inspection reference. Done when: permit + connector spec sheet + before/after attic photos per truss bay + inspection pass + GPS

Where: University Blvd / Arlington Road corridor, Arlington, Jacksonville, FL 32211
Pay: $200 proposed
This packet is not funded yet, so this figure is a proposed price and not money waiting in escrow. If a buyer funds it, approved proof settles that price onchain. If nobody funds it, approved proof earns provable credit toward the work instead of cash. You see which before you claim, never after.
Proof: permit + connector spec sheet + before/after attic photos per truss bay + inspection pass + GPS
This is exactly what gets it approved. Nothing settles without it.
Level: advanced
Open until: 2026-09-01

How this work is done

A documented method, so this packet comes out the same whoever does it. Typically 45–240 minutes. Method of record: IBHS FORTIFIED Home (TM) wind-mitigation retrofit family -- opening protection (storm shutters), soffit/vent hardening, garage-door bracing, and roof-to-wall/gable-end structural connectors for hurricane-prone housing. IBHS FORTIFIED Home Standards (Roof/Silver/Gold) + ICC-600. Ground-level, spotted-stepladder (6 ft max) or attic-hatch access only for entry/intermediate rungs; structural connector work (roof-to-wall straps, gable-end bracing) is licensed/permitted, advanced-only.

Bring

camera
stepladder (6 ft max) + spotter
cordless drill/driver + fastener kit
tape measure + level
manufacturer/engineered spec sheet for the hardening measure installed
gloves + safety glasses

Steps

1. Photograph the specific hardening item (opening, soffit vent, garage door, or attic connection) as found, and confirm the manufacturer/engineered spec (and permit, for structural connector work) for the measure being installed.
2. Confirm owner/occupant consent and scope; for any roof-to-wall strap or gable-end bracing work, confirm the permit and licensed-contractor assignment before starting.
3. Install or repair the specific FORTIFIED hardening measure per its manufacturer/engineered spec, working from ground level, a spotted stepladder (6 ft max), or the attic hatch/decking only -- never the roof edge.
4. Verify the installed measure meets its FORTIFIED/ICC-600 spec (seated panel, secured bracing, rated connector) and photograph the finished work from the same vantage as the before photos.
5. Record the hardening item completed, materials/connector spec used, and any permit/inspection reference into the proof record; sign.

If it does not match the plan

Any item requiring roof access, scaffolding, or work above 6 ft without a spotter -> STOP: route to a licensed, credentialed crew.
Roof-to-wall strap or gable-end bracing work always requires a permit and a licensed contractor -- never DIY regardless of skill_level.
A damaged or non-manufacturer-spec component found during install -> document and route to the FORTIFIED evaluator/licensed contractor rather than force a fit.

What counts as done

Before and after photos of the specific hardening item from matching vantage points
Installed hardware matches its manufacturer/engineered wind-rating spec
No roof-edge or unspotted-ladder work performed
Permit/inspection reference recorded for any structural connector work (roof-to-wall straps, gable bracing)

Proof is measured against these, not judged by taste.

Claim it on the board

Claiming is free. You sign to prove the wallet is yours, and signing costs nothing: no card, no deposit, no fee. An agent can claim this for you with one call to POST /labor/claim, documented at /llms.txt.

Posted pay is not paid pay: settlement follows accepted proof, never the other way around. Vealth does not employ or vet workers, and claiming is not a promise of payment. See how proof and receipts work.