Install a range-hood exhaust upgrade, St. Aloysius parish kitchen

The IAQ baseline in the parish kitchen found CO2/humidity climbing past reference levels during service — a proper exhaust upgrade is what actually fixes what the reading found. Standard: ASHRAE 62.1 ventilation + EPA IAQ baseline (CO2, PM2.5, VOC, RH); LBC Health+Happiness petal. Proof: Before photo of the existing exhaust + Install photos of the upgraded hood/duct run + Airflow test photo/video at the exterior vent cap Method (ASHRAE 62.1 ventilation + EPA IAQ baseline (CO2, PM2.5, VOC, RH); LBC Health+Happiness petal.): 1. Photograph the existing range hood/exhaust and confirm the duct route to the exterior. 2. Mount the upgraded exhaust fan/hood insert per its rough-in spec. 3. Connect the duct to the exterior vent cap and the switch wiring per a licensed electrician's hookup. 4. Test for proper exterior airflow and photograph the finished install. Done when: Before photo of the existing exhaust + Install photos of the upgraded hood/duct run + Airflow test photo/video at the exterior vent cap

Where

St. Aloysius Catholic Church, 2165 W Broad St, Columbus OH 43223

Pay

$110 proposed

This packet is not funded yet, so this figure is a proposed price and not money waiting in escrow. If a buyer funds it, approved proof settles that price onchain. If nobody funds it, approved proof earns provable credit toward the work instead of cash. You see which before you claim, never after.

Proof

Before photo of the existing exhaust + Install photos of the upgraded hood/duct run + Airflow test photo/video at the exterior vent cap

This is exactly what gets it approved. Nothing settles without it.

Level

intermediate

Open until

2026-09-01

How this work is done

A documented method, so this packet comes out the same whoever does it. Typically 45–90 minutes. Method of record: ASHRAE 62.1 + EPA IAQ / moisture baseline

Bring

• CO2 monitor
• PM2.5 monitor
• temp/RH meter
• moisture meter (mold/moisture scope)
• GPS/address
• camera

Steps

1. 1. Confirm the room/unit and address; coordinate to sample during normal occupancy where relevant.
2. 2. Photograph the space and any staining/damp/mold.
3. 3. Place the monitor in the occupied zone; log CO2 over >=1 occupied hour.
4. 4. Record PM2.5, temperature, and relative humidity.
5. 5. For moisture/mold scope, take moisture-meter readings at affected vs baseline areas and estimate visible mold area.
6. 6. Note ventilation type and any obvious deficiencies.
7. 7. Enter the logs, readings, extent notes, photos into the proof record; sign.

If it does not match the plan

• Carbon monoxide > 9 ppm sustained in an occupied space, or any audible CO alarm -> STOP: life-safety hazard. Evacuate, ventilate, and call the gas utility / fire department now. The agent escalates immediately, never sources the leak (NIOSH/ASHRAE CO).
• CO2 sustained > 2000 ppm in an occupied space -> flag acute under-ventilation: recommend increasing outdoor air and reducing occupancy immediately and report to the facility manager (well above the 1000 ppm ASHRAE 62.1 comfort flag).
• CO2 sustained > 1000 ppm -> flag under-ventilation vs ASHRAE 62.1.
• PM2.5 > 35 ug/m3 (24-hr, EPA NAAQS) -> flag elevated particulate; > 55 ug/m3 -> recommend occupants limit exposure / use filtration now.
• Visible mold > 10 sq ft OR active water intrusion -> document only, do not disturb; route to a licensed remediation pro (EPA mold guidance); occupants with respiratory symptoms routed to relocate.

What counts as done

• CO2 logged over >=1 occupied hour
• PM2.5, temperature, and RH recorded
• Moisture readings + visible-mold extent recorded (moisture scope)
• Timestamped photos + address confirm

Proof is measured against these, not judged by taste.