advanced work · 1000 Irving St, Westwood, Denver, CO 80219

Replace the gas furnace with a heat pump, Home on Irving St (1000 block), Westwood

This Irving St home's gas furnace burns fuel for every hour of Denver's long heating season over a grid that gets cleaner every year; a right-sized, cold-climate heat pump is the direct Energy-Petal repair the readiness walk above pointed at — and it cools too, which the furnace can't. Standard: Heat-pump HVAC replacement — ACCA Manual J/S sizing, manufacturer + local mechanical/electrical permits (LBC Energy petal). SDG 7. Proof: permit + commissioning sheet + before/after photos + inspection result + GPS Method (Heat-pump HVAC replacement — ACCA Manual J/S sizing, manufacturer + local mechanical/electrical permits (LBC Energy petal). SDG 7.): 1. Verify Manual J/S sizing for Denver's 5,280 ft climate zone against the home and photograph the existing furnace and nameplates; confirm permit and electrical capacity before work. 2. Recover refrigerant from any old unit per EPA 608 and remove equipment for documented disposal. 3. Set the new cold-climate heat pump, run the line set, pull vacuum to spec and charge per manufacturer; a licensed electrician lands the circuit and disconnect. 4. Commission: verify charge, airflow, heating/cooling delta-T at altitude, and condensate; set up the thermostat. 5. Pass the mechanical/electrical inspection and photograph the commissioning readings and finished installation. Done when: permit + commissioning sheet + before/after photos + inspection result + GPS

Where: 1000 Irving St, Westwood, Denver, CO 80219
Pay: $225 proposed
This packet is not funded yet, so this figure is a proposed price and not money waiting in escrow. If a buyer funds it, approved proof settles that price onchain. If nobody funds it, approved proof earns provable credit toward the work instead of cash. You see which before you claim, never after.
Proof: permit + commissioning sheet + before/after photos + inspection result + GPS
This is exactly what gets it approved. Nothing settles without it.
Level: advanced
Open until: 2026-09-01

How this work is done

A documented method, so this packet comes out the same whoever does it. Typically 360–720 minutes. Method of record: Heat-pump HVAC replacement sized by ACCA Manual J/S, installed per manufacturer + local mechanical/electrical permits (ENERGY STAR cold-climate list where applicable) — licensed crew; assess→install→verify

Bring

Manual J/S load calculation + approved permit
heat-pump equipment (outdoor + indoor units), line set, pad/brackets, condensate handling
refrigerant gauges/scale + vacuum pump + torque tools (EPA 608-certified technician)
multimeter + thermometer/anemometer for commissioning airflow and delta-T

Steps

1. ASSESS: verify the Manual J/S sizing against the home (envelope, ductwork or head locations), confirm electrical capacity for the new circuit, and photograph the existing system and nameplates.
2. Decommission and recover refrigerant from the old system per EPA 608; remove equipment for lawful disposal/recycling and document it.
3. Set and mount the new equipment, run and braze/flare the line set, pull vacuum to spec, and release/weigh in charge per manufacturer; a licensed electrician lands the new circuit and disconnect.
4. Commission: verify airflow, refrigerant charge (subcooling/superheat per spec), heating and cooling delta-T, and condensate drainage; set up controls/thermostat.
5. VERIFY: pass the mechanical/electrical inspection; record commissioning numbers and before/after photos; leave the owner the manual, warranty registration, and maintenance schedule.

If it does not match the plan

Load calc missing or equipment more than one size off Manual S -> STOP: resize before install.
Electrical panel cannot support the new circuit -> route to panel/service upgrade first; never overload.
Refrigerant handling by non-EPA-608-certified person -> STOP.

What counts as done

Old refrigerant recovered and disposal documented (EPA 608)
Commissioning sheet complete: vacuum level, charge method, delta-T, airflow within manufacturer spec
Permit inspection(s) passed; disconnect and circuit labeled
Before/after photos + nameplate photos on file

Proof is measured against these, not judged by taste.

Claim it on the board

Claiming is free. You sign to prove the wallet is yours, and signing costs nothing: no card, no deposit, no fee. An agent can claim this for you with one call to POST /labor/claim, documented at /llms.txt.

Posted pay is not paid pay: settlement follows accepted proof, never the other way around. Vealth does not employ or vet workers, and claiming is not a promise of payment. See how proof and receipts work.