Install low-flow aerators and showerheads at a host-invited Delano congregation site

Congregation kitchens and restrooms in Delano often still run fixtures from the 1980s that pour twice the water they need in a region where every acre-foot is contested. Swapping aerators and heads for WaterSense-rated fixtures takes an afternoon and saves thousands of gallons a year. The water bill savings stay with the community. Standard: EPA WaterSense fixture specifications; SDG 6 Clean Water and Sanitation. Proof: Photos of each new fixture running plus swap count with GPS/date Method (EPA WaterSense fixture specifications; SDG 6 Clean Water and Sanitation.): 1. Walk the site's restrooms and kitchen with the host and list every faucet and showerhead. 2. Unscrew old aerators, clean the threads, and install WaterSense-rated replacements with tape-sealed threads. 3. Replace any showerheads with 1.8 gpm WaterSense models. 4. Run each fixture to confirm flow and check for drips at every new connection. 5. Photograph each swapped fixture running and record the count with GPS and date. Done when: Photos of each new fixture running plus swap count with GPS/date

Where

Host-invited congregation site near Main St & 9th Ave, Delano, CA 93215

Pay

$80 proposed

This packet is not funded yet, so this figure is a proposed price and not money waiting in escrow. If a buyer funds it, approved proof settles that price onchain. If nobody funds it, approved proof earns provable credit toward the work instead of cash. You see which before you claim, never after.

Proof

Photos of each new fixture running plus swap count with GPS/date

This is exactly what gets it approved. Nothing settles without it.

Level

entry

Open until

2026-09-01

How this work is done

A documented method, so this packet comes out the same whoever does it. Typically 45–90 minutes. Method of record: EPA WaterSense fixture flow-rate + leak audit

Bring

• flow-rate measurement bag + timer
• toilet dye tablets
• moisture meter
• GPS / address
• camera
• tablet / data sheet

Steps

1. 1. Confirm the address; get a staff escort; photograph each fixture group.
2. 2. Measure flow rate at each faucet/shower with the bag-and-timer method; record gallons per minute (gpm).
3. 3. Test each toilet for leaks with a dye tablet (wait 10 min, check for color in the bowl); record flush volume.
4. 4. Inspect fixtures, meters, and irrigation for visible leaks/drips; note each.
5. 5. Read the water meter with all fixtures off; note any movement (indicates a hidden leak).
6. 6. Rank WaterSense fixture upgrades + leak repairs by estimated water/cost savings.
7. 7. Record flow rates, leak results, meter check, ranked measures, and photos into the proof record; sign.

If it does not match the plan

• Meter moving with all fixtures off AND active water damage (wet drywall, ceiling stain, pooling near electrical) -> STOP: possible electrical exposure; keep clear, route to a licensed plumber (and electrician if water contacts wiring). The agent documents, never opens walls.
• Suspected cross-connection / backflow risk (hose-bib, irrigation, boiler makeup) -> flag for a licensed plumber backflow test; potable-water contamination is a health hazard — do not test-operate the connection.
• Toilet dye migrates into the bowl -> flag a leaking flapper/valve for repair.
• Meter moves with all fixtures off -> flag a hidden leak for investigation.
• Faucet > 2.2 gpm or showerhead > 2.0 gpm -> recommend a WaterSense upgrade.
• No electrical/gas work; documentation only — flag suspected pipe damage, do not disassemble.

What counts as done

• Flow rate (gpm) recorded per fixture
• Toilet leak result + flush volume recorded per toilet
• Meter-with-all-off check recorded
• Ranked upgrade/repair measures + photos + address confirm

Proof is measured against these, not judged by taste.