Seal the drafts at an invited McFarland home before the heat peaks

McFarland's older homes leak cooled air through gapped doors and window frames all summer, and the power bill lands on families already stretched. Weatherstrip, sweeps, and rope caulk on the worst openings is an afternoon of work that pays back every month. Small fixes, done well, done now. Standard: DOE air-sealing guidance for doors and windows; SDG 7 Affordable and Clean Energy. Proof: Before/after photos per opening with GPS/date Method (DOE air-sealing guidance for doors and windows; SDG 7 Affordable and Clean Energy.): 1. Walk the home with the occupant and list the draftiest doors and windows. 2. Clean frames and install matched weatherstrip on each flagged opening. 3. Fit sweeps on exterior doors and rope caulk on leaky window sashes. 4. Test each opening with a dollar-bill pull and adjust to snug. 5. Photograph each sealed opening before and after and record with GPS and date. Done when: Before/after photos per opening with GPS/date

Where

Host-invited home near Second St & Hanawalt Ave, McFarland, CA 93250

Pay

$80 proposed

This packet is not funded yet, so this figure is a proposed price and not money waiting in escrow. If a buyer funds it, approved proof settles that price onchain. If nobody funds it, approved proof earns provable credit toward the work instead of cash. You see which before you claim, never after.

Proof

Before/after photos per opening with GPS/date

This is exactly what gets it approved. Nothing settles without it.

Level

entry

Open until

2026-09-01

How this work is done

A documented method, so this packet comes out the same whoever does it. Typically 45–120 minutes. Method of record: US DOE Weatherization Assistance Program DIY-safe air-sealing measures + ENERGY STAR DIY Guide to Sealing and Insulating. Occupant-safe caulk/weatherstrip work only; no combustion, electrical, insulation-removal, or pre-1978 paint disturbance.

Bring

• camera
• caulk gun + paintable/silicone caulk
• weatherstripping + door sweeps
• foam outlet/switch gaskets
• utility knife + putty knife
• tape measure
• gloves + safety glasses

Steps

1. 1. Photograph each draft location (window trim, door, outlet, penetration) before sealing.
2. 2. Confirm the home is post-1978 or the surfaces are lead-safe; if pre-1978 with disturbed paint, STOP and flag for a lead-safe pro.
3. 3. Clean and dry each gap; remove old failed caulk/weatherstrip with the putty knife.
4. 4. Apply a continuous caulk bead to fixed gaps (window/door trim, penetrations) and tool it smooth.
5. 5. Install weatherstripping on operable window/door edges so it compresses without binding the sash/door.
6. 6. Fit door sweeps to exterior doors and foam gaskets behind outlet/switch plates on exterior walls.
7. 7. Verify each treated opening closes/latches and the seal is continuous; photograph the finished work.
8. 8. Enter locations sealed, materials used, before/after photos, and any flagged hazard into the proof record; sign.

If it does not match the plan

• Pre-1978 home with peeling/chipping paint on the work surface -> STOP: do not scrape/disturb; route to an EPA RRP lead-safe certified pro.
• Gas appliance, water heater, or fireplace in the space -> do not tighten a combustion-air/venting path; leave required make-up air and flag for a weatherization pro (backdraft/CO risk).
• Active moisture, mold, or rot at the opening -> fix the moisture source first; do not seal moisture in.

What counts as done

• Before and after photos of each sealed location
• Continuous caulk bead on fixed gaps and weatherstripping that compresses without binding
• Door sweeps and outlet gaskets installed on exterior openings/walls as scoped
• Every treated door/window still closes and latches after sealing

Proof is measured against these, not judged by taste.