Rake the storm drains clear on Lumberton's flood streets before every big rain (2026-07-19)

Lumberton floods from the river, but its streets flood first from blocked drains — leaves, litter, and storm trash cap the inlets exactly when the water comes. A standing monthly round that rakes the grates clear buys the whole block drainage time in every storm. Standard: City stormwater maintenance practice (surface clearing); SDG 11 (Sustainable Cities and Communities). Proof: before/after photos of each cleared grate plus the route log Method (City stormwater maintenance practice (surface clearing); SDG 11 (Sustainable Cities and Communities).): 1. Walk the assigned flood-street blocks, prioritizing before forecast heavy rain. 2. Rake debris off each grate from the curb, keeping hands and tools out of the opening. 3. Bag the debris — never sweep it back to the street. 4. Log each cleared inlet. 5. Photograph each grate before and after, GPS-tagged and dated. Done when: before/after photos of each cleared grate plus the route log

Where

Storm inlets near W 2nd St & N Pine St, Lumberton, NC 28358

Pay

$168 proposed

This packet is not funded yet, so this figure is a proposed price and not money waiting in escrow. If a buyer funds it, approved proof settles that price onchain. If nobody funds it, approved proof earns provable credit toward the work instead of cash. You see which before you claim, never after.

Proof

before/after photos of each cleared grate plus the route log

This is exactly what gets it approved. Nothing settles without it.

Level

entry

Open until

2026-08-19

How this work is done

A documented method, so this packet comes out the same whoever does it. Typically 60–180 minutes. Method of record: Storm drain inlet surface cleaning + minor grate/apron repair per EPA MS4 stormwater BMP maintenance — SURFACE WORK FROM THE CURB ONLY; never enter the drain, never lift beyond the grate; assess→clear/repair→verify

Bring

• heavy work gloves + hi-vis vest + grabber tool and rake
• contractor bags for debris (landscape debris separated from trash)
• camera + measuring tape
• cones for the curb work zone (stay out of the traffic lane)

Steps

1. 1. ASSESS: photograph the inlet as found (grate, apron, gutter approach), note blockage type and any damage (broken grate, displaced apron concrete), and record GPS.
2. 2. Set cones at the curb work zone; all work is from the sidewalk/curb — never step into the traffic lane and never enter, reach into, or open the drain structure.
3. 3. Clear debris, sediment, and litter from the grate surface and the gutter approach with the rake/grabber; bag and dispose of it properly (green waste separated).
4. 4. Minor repair within surface scope: re-seat a displaced grate that lifts freely by hand from above, patch apron spalls with cold-patch where the city standard allows; anything more is documented, not attempted.
5. 5. VERIFY: photograph the cleared inlet from the same vantage, pour a bucket of clean water at the gutter approach to show flow into the inlet, and report any structural damage to the municipal stormwater line (311/MS4 contact) with photos.

If it does not match the plan

• Anything requiring entry, reaching into the barrel, or lifting a seized grate -> STOP: document and report to the municipality; surface work only.
• Suspected illicit discharge (odor, sheen, off-color flow) -> do not touch; photograph from the curb and report to the MS4 hotline immediately.
• Inlet on a high-speed road with no safe curb work zone -> document from the sidewalk only and report; never work in the traffic lane.

What counts as done

• Before/after photos from matching vantage show the grate and gutter approach clear
• Water-flow photo/video shows drainage into the inlet with no ponding at the approach
• Debris bagged and disposed (photo), green waste separated
• Any structural damage reported to the municipal stormwater contact with the report reference recorded

Proof is measured against these, not judged by taste.