Walk the safety checklist at a equipment servicing job in Tulsa, OK (2026-07-21)

A equipment servicing job in Tulsa, OK needs an independent, documented pre-task safety walk against the standard checklist — never trade work, only observation, photos, and a tiered findings list routed to the site's competent person. Standard: OSHA 29 CFR 1926.417 (Lockout and tagging of circuits) + 29 CFR 1910.147 (Control of Hazardous Energy) by reference Proof: photo of each energy-isolating device's lock/tag + GPS + LOTO checklist + tiered findings Method (OSHA 29 CFR 1926.417 + 1910.147 control-of-hazardous-energy (LOTO) observation — verification of applied locks/tags, isolation, stored-energy relief, and group lockout; documentation only, ~30-60 min): 1. Check in with the authorized employee / competent person; confirm scope, don PPE, and confirm you observe-and-document only — you never operate an energy-isolating device and never apply or remove any lock or tag (only the employee who applied a lock may remove it, per 1910.147). 2. Confirm a written, equipment-specific energy-control procedure exists and identifies every energy source (electrical, mechanical, hydraulic, pneumatic, thermal, gravity/stored) (§1910.147(c)(4)). 3. Photograph each energy-isolating device and confirm it carries the authorized employee's lock and a durable tag with their name, with the device in the safe/isolated position (§1910.147(d)). 4. Confirm stored/residual energy is relieved, disconnected, restrained, or otherwise rendered safe (capacitors, springs, elevated parts, pressure, heat) (§1910.147(d)(5)). 5. For multi-worker servicing, confirm a group-lockout device/box is used so each authorized employee has an individual lock; document the count of workers vs locks (§1910.147(f)(3)). 6. For each finding, mark the condition against the LOTO checklist item, assign a tier (stop-work / correct-before-proceed / monitor), and name the responsible authorized employee / competent person. 7. Enter photos, GPS/address, the checklist, and the tiered findings; sign. Route stop-work items to the authorized employee / competent person with a timestamp — never touch a lock, tag, or energy control. Equipment: hard hat + safety glasses + hi-vis vest (site PPE), tablet/clipboard with the 29 CFR 1910.147 LOTO checklist, camera, the equipment's written energy-control procedure (for reference), flashlight Done when: Written equipment-specific energy-control procedure confirmed present (or its absence flagged) with all energy sources identified; Each energy-isolating device photographed with the authorized employee's lock + durable named tag, in the isolated position; Stored/residual-energy relief and (for multi-worker jobs) group-lockout individual-lock coverage documented; Every finding tiered with the authorized employee / competent person named; stop-work items routed with a timestamp

Where

Equipment servicing job, Tulsa, OK

Pay

$512 proposed

This packet is not funded yet, so this figure is a proposed price and not money waiting in escrow. If a buyer funds it, approved proof settles that price onchain. If nobody funds it, approved proof earns provable credit toward the work instead of cash. You see which before you claim, never after.

Proof

photo of each energy-isolating device's lock/tag + GPS + LOTO checklist + tiered findings

This is exactly what gets it approved. Nothing settles without it.

Level

entry

Open until

2026-07-28

How this work is done

A documented method, so this packet comes out the same whoever does it. Typically 30–60 minutes. Method of record: OSHA 29 CFR 1926.417 + 1910.147 control-of-hazardous-energy (LOTO) observation — verification of applied locks/tags, isolation, stored-energy relief, and group lockout; documentation only

Bring

• hard hat + safety glasses + hi-vis vest (site PPE)
• tablet/clipboard with the 29 CFR 1910.147 LOTO checklist
• camera
• the equipment's written energy-control procedure (for reference)
• flashlight

Steps

1. 1. Check in with the authorized employee / competent person; confirm scope, don PPE, and confirm you observe-and-document only — you never operate an energy-isolating device and never apply or remove any lock or tag (only the employee who applied a lock may remove it, per 1910.147).
2. 2. Confirm a written, equipment-specific energy-control procedure exists and identifies every energy source (electrical, mechanical, hydraulic, pneumatic, thermal, gravity/stored) (§1910.147(c)(4)).
3. 3. Photograph each energy-isolating device and confirm it carries the authorized employee's lock and a durable tag with their name, with the device in the safe/isolated position (§1910.147(d)).
4. 4. Confirm stored/residual energy is relieved, disconnected, restrained, or otherwise rendered safe (capacitors, springs, elevated parts, pressure, heat) (§1910.147(d)(5)).
5. 5. For multi-worker servicing, confirm a group-lockout device/box is used so each authorized employee has an individual lock; document the count of workers vs locks (§1910.147(f)(3)).
6. 6. For each finding, mark the condition against the LOTO checklist item, assign a tier (stop-work / correct-before-proceed / monitor), and name the responsible authorized employee / competent person.
7. 7. Enter photos, GPS/address, the checklist, and the tiered findings; sign. Route stop-work items to the authorized employee / competent person with a timestamp — never touch a lock, tag, or energy control.

If it does not match the plan

• Servicing/maintenance underway on equipment that is NOT locked out (no lock/tag on the energy-isolating device) -> STOP-WORK: document, keep clear, route to the authorized employee / competent person; never apply the lockout yourself.
• A tag without a lock where the device accepts a lock, or a lock without the authorized employee's identifying tag -> flag correct-before-proceed to the authorized employee.
• Stored/residual energy not relieved (charged capacitor, pressurized line, elevated/unblocked load) -> STOP-WORK; keep clear; route to the authorized employee / a qualified person; never discharge or restrain it yourself.
• Any application/removal of a lock or tag, operation of an energy-isolating device, or energy verification (test-for-dead) -> observe-and-document only; the authorized employee performs and approves these. Approval and correction stay human.

What counts as done

• Written equipment-specific energy-control procedure confirmed present (or its absence flagged) with all energy sources identified
• Each energy-isolating device photographed with the authorized employee's lock + durable named tag, in the isolated position
• Stored/residual-energy relief and (for multi-worker jobs) group-lockout individual-lock coverage documented
• Every finding tiered with the authorized employee / competent person named; stop-work items routed with a timestamp

Proof is measured against these, not judged by taste.