← Board

Succ Water Efficiency Self Realization Fellowship Lake Shrine

Install the low-flow aerators and showerheads the audit finds.

Replace the old aerators and showerheads at a community building in Pacific Palisades, CA with certified low-flow ones, which cuts the draw Read all of it

Not funded yet. Settles as earned credit, $95 proposed.

Proof it takes, the deadline, the level
  • Proofbefore/after flow-rate readings per fixture + WaterSense label photo + leak retest + GPS
  • Open until2026-10-23
  • Levelintermediate
All of it: the words, the place, the proof

Replace the old aerators and showerheads at a community building in Pacific Palisades, CA with certified low-flow ones, which cuts the draw immediately. The water audit is expected to find them running above WaterSense flow limits. Fixtures running above the WaterSense flow limits are wasteful and send extra gallons down the drain with every use. Name the exact site and confirm it with its host before you claim: this listing gives only the area. For the payer: - Price: $95 per job, counted in fixtures replaced. - Likely payer: LADWP rebate programs, paid to the account holder after the program's pre-approval. - No license is needed while the whole job, labor and materials together, stays under $1,000 (Business and Professions Code section 7048); at $1,000 or more, a CSLB C-36 Plumbing license (pipe work behind a wall needs it at any price).

Fund it for $95. The receipt lands onchain once the proof is approved.

What it looks like
A worker turns an adjustable wrench on an aerator or valve at the site, swaps in a certified low-flow replacement, then reads the flow in a gallon-marked bucket.

A description of this kind of work, not a record that it happened here.

Where
Succ Water Efficiency Self Realization Fellowship Lake Shrine, a community building in Pacific Palisades, CA. Open the map
Pay
$95 proposed

This job is not funded yet, so this figure is a proposed price, not money held for the worker. If a buyer funds it, approved proof settles that price onchain. If nobody funds it, approved proof earns provable credit toward the work instead of cash: recorded, and readable any time at vealth.net/labor/credit/(your wallet). You see which before you claim, never after.

Proof
before/after flow-rate readings per fixture + WaterSense label photo + leak retest + GPS

This is exactly what gets it approved. Nothing settles without it.

Level
intermediate
Open until
2026-10-23
Posted by
0x034F…6c89

The creator wallet. Its signature is what approves proof and settles the wage.

Safety, read before you claim

Start after the crew's safety orientation. Close the fixture's own supply stop before opening it where one is in reach and turns freely (a showerhead is swapped with the shower valve off), and never turn a building main, meter, backflow-prevention or fire-line fitting or force a stop that weeps or will not close. Aerators and showerheads only, in nitrile gloves and eye protection, with cold water for flow tests; a toilet or any pipe or valve work is licensed plumbing, so stop and tell the owner; wear slip-resistant closed-toe shoes.

The full safety list for this job:

  • The swap asks for no licence; only a licensed plumber may solder or sweat copper.
  • Get occupant or manager consent first, and never remove a fixture before shutting off the local supply.
  • Old multi-turn stops often leak the first time they move in years: if one weeps, close the handle, stop, and report it to the owner. A showerhead has no supply valve of its own, so do not hunt for one; keep water from being pushed at the face. Test flow with cold water; hot lines scald and the water heater setting is the owner's. A swap says nothing about water quality, lead in old brass, or the pipes behind the wall; never call the water fit to drink. Wrap chrome in cloth or tape before gripping with a wrench. Hand every old part back to the owner in a bag.
  • Orientation to the site's injury and illness plan before touching a fixture: who to call, where first aid is, what to stop for (Title 8 section 3203).
  • Restrooms and closets run hot: water, a cool place to rest, watch each other for heat signs (use the outdoor heat plan, section 3395, for hose bibs and exterior fixtures) (Title 8 section 3396).
  • Eye protection under a sink or overhead at a shower arm: scale and debris fall in the face (Title 8 section 3382).
  • Wear gloves and closed-toe shoes (Title 8 section 3384).
  • Footwear, Title 8 section 3385: slip-resistant closed-toe shoes for wet floors and dropped fixtures.
  • Outdoors: wildfire smoke, section 5141.1: at a PM2.5 AQI of 151 or more the employer provides N95 respirators for voluntary use and moves the work indoors or cuts exposure where feasible; above AQI 500 respirators are required under a respiratory protection program.
  • Outdoors: heat, section 3395: drinking water, shade and cool-down rests; shade is ready at 80 F and the high-heat steps start at 95 F.
How this work is done

How this work is done

A documented method, so this packet comes out the same whoever does it.

Bring

  • an adjustable wrench to remove the targeted aerator or valve and a bucket marked in gallons to record each flow rate
  • bucket or flow bag marked in gallons and a phone timer
  • cloth or masking tape to protect chrome
  • eye protection
  • aerator key for tamper-resistant aerators
  • a bag for old parts

Steps

  1. Obtain two things in writing before any work: the owner's or manager's consent for this work at this address, and, when an LADWP rebate pays for it, the rebate pre-approval (SoCal WaterSmart) with the pre-approval photos taken as the program asks. Work done before the pre-approval can be ineligible, so the start waits for it. Write both at the top of your proof.
  2. Get the owner or manager's written consent and the building and room list before anything else (a block title is not a building). Then locate each old aerator or showerhead this job targets at the site its title names.
  3. Record the exact community-building site, street address, and host contact.
  4. With the old fixture still running, run cold water into a marked bucket or bag for a timed 10 or 15 seconds and write down the volume and the seconds, so the gallons per minute can be recomputed from your numbers.
  5. Record the before flow rate for each targeted aerator or showerhead fixture.
  6. Aerator: close the faucet and use its own stop only if it turns freely. Showerhead: shower valve off, no stop at all. Never go find a unit or building valve.
  7. Install aerators and showerheads only, chosen to meet California's limits as well as the WaterSense label (showerheads 1.8 gpm, residential lavatory faucets 1.2 gpm, public restroom lavatory faucets 0.5 gpm; verify the current CALGreen and Title 20 figures). Toilets move to a licensed plumber.
  8. Photograph the WaterSense label on each replacement part before fitting it.
  9. Remove the targeted aerator or showerhead and install the certified low-flow replacement.
  10. Leave toilets, flush valves and any pipe or valve work to the licensed plumber. If you find a running toilet on the walk, report it to the owner; do not repair it.
  11. Record the after flow rate for each targeted aerator or showerhead.
  12. Photograph the installed fixtures and record the GPS.

What counts as done

  • Before flow-rate reading (gpm) per targeted fixture
  • WaterSense label photo of each installed fixture
  • After flow-rate reading confirming the reduction
  • After photo or video of each new part running with no drip at its thread
  • Site record: the exact site's name and street address, and the contact who agreed to the work
  • The owner's or manager's consent, on the record.
  • The room for each fixture.
  • The timed bucket reading (gallons and seconds) before and after each fixture; a list of gpm numbers alone cannot be checked.
  • Photo of the old part in hand beside the new part's label.
  • Consent: the owner's or manager's written consent, naming the address and the work, dated before the first photo.
  • Pre-approval first: the LADWP rebate program's pre-approval or reservation number and date, from before any work, or the words 'no rebate' when none is claimed.
  • Completion matches the pre-approval: the pre-work photos taken for it, and the completion measurements (fixture count and the flow rate or WaterSense label) that match what the program approved.
  • Sign-off: the owner or manager signs off the finished work in writing, and LADWP's completion review accepts the record when a rebate pays for it. Write who signed and the date, or the date you asked.
  • Photos: take the before photo and the after photo from the same point (stand where the first one was taken and match its frame), each with its GPS point and its date and time.

Proof is measured against these, not judged by taste.

The standard this serves

Water Efficiency. Water efficiency is the quiet discipline of wasting nothing indoors. The EPA's WaterSense program sets the marks: how many gallons a minute a faucet should pass, how to find the leak that runs a toilet all night, how a household's water bill tells a story. Mastery looks like an auditor who can walk a home in an hour and find every hidden gallon. The skill is built one fixture at a time, which is exactly what this packet asks: measure one flow, find one leak, record one truth about where the water goes.

What is promised, and what is not

Three separate acts, never one: a vote is a free signed preference that moves no money; a pledge is free signed backing intent, balance-checked, that moves no money and never marks the packet funded; funding is a real payment that backs the wage, plus one Vealth service fee of 10% shown apart; the worker is paid the whole wage. Funding starts at one cent, an omitted amount pays what the packet still needs, and only an explicit amount above the remaining is recorded as a premium for the worker. Money settles only on accepted proof. An agent can fund it in one x402 call: POST /nurture/fund {"workId":"WORK_1784868600901_vx0amuu","funderWallet":"0xYOU"}.

Claiming is free. You sign to prove the wallet is yours: no card, no deposit, no fee. Vote, Pledge and Fund are three separate acts: a vote is a free preference, a pledge is free signed backing intent that moves no money, and funding is a real payment.

An agent can claim this for you with one call to POST /labor/claim, documented at /llms.txt.

Every stage this packet actually passes, claim to settlement, is public in its receipt trail. A stage that has not happened is not claimed.

Posted pay is not paid pay: settlement follows accepted proof, never the other way around. Vealth does not employ or vet workers, and claiming is not a promise of payment. See how proof and receipts work.

Other acts: vote, pledge, fund

Packet WORK_1784868600901_vx0amuu