Install a point-of-use water filter.

A worker shuts off the supply and mounts a certified point-of-use filter on the tap at rural well near Gallup, then photographs the NSF/ANSI label and a retest reading confirming the water is safe. Read all of it

Lapsed. Nothing is owed and nothing is waiting.

This packet has expired.

It is kept here so the link never dies. See work that is open now.

All of it: the words, the place, the proof

Install an NSF/ANSI-certified point-of-use filter on the tap or spigot this source feeds at rural well near Gallup, NM. The potability test flagged a contaminant, so size the filter to it and confirm the fix with a retest. The water this tap delivers was flagged by a potability test for a contaminant that needs treatment.

This one lapsed at $85. Similar work is open on the board.

What it looks like: A worker shuts off the supply and mounts a certified point-of-use filter on the tap at rural well near Gallup, then photographs the NSF/ANSI label and a retest reading confirming the water is safe.
A description of this kind of work, not a record that it happened here.
Where: Succ Drinking Water Safety, rural well near Gallup, NM. Open the map
Pay: $85 lapsed
This job expired before anyone claimed it. Nothing is owed and nothing is waiting.
Proof: before/after test readings + NSF/ANSI label photo + install date/next-service label + GPS waypoint: Real, Proven, One-of-one
This is exactly what gets it approved. Nothing settles without it.
Level: intermediate
Lapsed: 2026-10-23
Posted by: 0x034F…6c89
The creator wallet. Its signature is what approves proof and settles the wage.

Safety, read before you claim

Shut off local supply before install, and no soldering or sweating copper without a licensed plumber. STOP and route to the water utility, the local health department, or a licensed plumber if the contamination is systemic.

The full safety list for this job:

A systemic municipal or utility-source contamination, or a whole-building lead result at or above the EPA action level, is not DIY-scoped.
Point-of-entry treatment and service-line work route to the water utility, the local health department, or a licensed plumber.

How this work is done

A documented method, so this packet comes out the same whoever does it.

Bring

NSF/ANSI 42/53/58-certified filter or treatment unit matched to the flagged contaminant
basic plumbing hand tools (wrench, tubing cutter, Teflon tape) or a certified installer for a whole-building POE unit
test strips or a second lab sample kit for the post-install retest
GPS device / phone for the waypoint

Steps

1. ASSESS: read the potability test result and pick an NSF/ANSI-certified device rated to reduce the specific contaminant flagged (lead/bacteria/nitrate/turbidity).
2. Shut off the local water supply and install the device at the point of use (or point of entry for a whole-building concern), following the manufacturer's instructions.
3. Flush and prime the new device per the manufacturer's start-up procedure before it is used for drinking water.
4. Post-install retest: run the same test the audit used and confirm the flagged contaminant is now below the safety threshold.
5. VERIFY: label the unit with the install date + next filter-change date, and leave the household/site a plain-language card explaining what it does and when to service it.

What counts as done

Photo of the flagged test result being remedied
NSF/ANSI certification label photo of the installed device
Post-install retest reading confirming the contaminant is below the safety threshold
GPS waypoint of the installed device

Proof is measured against these, not judged by taste.

What is promised, and what is not

Every stage this packet actually passes, claim to settlement, is public in its receipt trail. A stage that has not happened is not claimed.

Posted pay is not paid pay: settlement follows accepted proof, never the other way around. Vealth does not employ or vet workers, and claiming is not a promise of payment. See how proof and receipts work.

Packet WORK_1784868861649_fqn18fz