Anyone can start here · Old Orchard Park, 2200 Old Orchard Dr, Diboll, TX 75941 (public city park)
Plant a native shrub understory beneath the park canopy at Old Orchard Park, site 1, Old Orchard Park, 2200 Old Orchard Dr, Diboll, TX 75941 (public city park) (2026-07-24)
This stretch of Old Orchard Park's pine and hardwood canopy has an open, mowed understory with none of the native shrub layer that would normally fill it, leaving less structure and food for East Texas piney-woods wildlife. Standard: ANSI A300 Part 6 (Planting) + ISA Best Management Practices for tree planting and establishment, Arbor Day Foundation planting standard. SDG 11.7/15 urban canopy. Proof: city-parks-department siting confirm + before/after photos + species/count record + GPS Method (ANSI A300 Part 6 (Planting) + ISA Best Management Practices for tree planting and establishment, Arbor Day Foundation planting standard. SDG 11.7/15 urban canopy.): 1. 1. Confirm the planting area with the city parks department, beneath existing pine and hardwood canopy in the park, clear of any irrigation line or buried utility, and photograph the bare understory before planting. 2. 2. Clear leaf litter and any invasive groundcover from the planting spots by hand without disturbing established canopy-tree roots. 3. 3. Plant a native shrub and small-tree understory mix suited to East Texas piney-woods forest at the design spacing. 4. 4. Water in and mulch each planting; photograph the finished planting from the matching before vantage and record species/count. Done when: city-parks-department siting confirm + before/after photos + species/count record + GPS
How this work is done
A documented method, so this packet comes out the same whoever does it. Typically 45–90 minutes. Method of record: ANSI A300 Part 6 (Planting) + ISA Best Management Practices for tree planting & establishment; Arbor Day Foundation planting standard. DIY-safe volunteer planting on cleared, utility-marked ground; no mechanized or utility-conflict digging.
Bring
- GPS-capable phone
- camera
- round-point shovel + digging fork
- hand pruners
- mulch (wood chips) + measuring stick
- watering can or hose
- gloves + closed-toe boots
Steps
- 1. Confirm the planting spot is inside the posting radius and clear of marked utilities (811 locate honored); record the GPS waypoint.
- 2. Photograph the bare site and the nursery stock (label/species visible) before planting.
- 3. Dig the hole 2-3x the root-ball width and no deeper than the root ball, so the root flare will sit at or just above grade.
- 4. Remove the container or cut away burlap/wire, gently loosen circling roots, and set the tree with the root flare visible at grade.
- 5. Backfill with the native soil in layers, firming out air pockets; do not bury the root flare or amend heavily.
- 6. Build a shallow watering basin, water in slowly until the backfill is saturated, and apply 2-3 inches of mulch kept 3 inches off the trunk.
- 7. Stake only if the tree cannot stand on its own; use two loose ties that allow trunk movement, and note a removal date within one year.
- 8. Record species, GPS, before/after photos, root-flare-at-grade confirmation, mulch depth, and water applied into the proof record; sign.
If it does not match the plan
- Unmarked or suspected buried utility, or the 811 locate is not honored -> STOP: do not dig; reschedule after a confirmed locate.
- Root ball is dry, circling/kinked, or the trunk is wounded -> do not plant as-is; soak/correct or reject the stock and note it, rather than establish a failing tree.
- Right-of-way, overhead-line conflict, or a species/site mismatch -> flag for the site steward and choose an approved spot/species; never plant into a conflict.
What counts as done
- GPS waypoint recorded inside the posting radius on utility-cleared ground
- Before and after photos showing the root flare visible at grade
- Mulch applied 2-3 inches deep and held off the trunk, with a watering basin formed and watered in
- Species and any staking (with a removal date) recorded in the proof
Proof is measured against these, not judged by taste.
Claiming is free. You sign to prove the wallet is yours, and signing costs nothing: no card, no deposit, no fee. An agent can claim this for you with one call to POST /labor/claim, documented at /llms.txt.
Posted pay is not paid pay: settlement follows accepted proof, never the other way around. Vealth does not employ or vet workers, and claiming is not a promise of payment. See how proof and receipts work.