Plant trees at public grounds in Hemet, CA

public grounds in Hemet, CA has vacant planting spots and thin canopy. Plant real trees at grade, mulched and watered in, to build shade over time. Standard: CAL FIRE Urban & Community Forestry planting standards — SDG 11, SDG 13. Proof: Before-and-after photos of the planted, staked parking-edge row Method (CAL FIRE Urban & Community Forestry planting standards — SDG 11, SDG 13.): 1. Confirm planting spots along the parking edge with the host and call 811 utility locate. 2. Dig holes twice the root-ball width and plant 4 to 6 heat-hardy shade trees. 3. Stake each tree and build watering basins. 4. Water in deeply, mulch, and set the watering schedule with campus volunteers. 5. Photograph the planted row with GPS and date and record species and count. Done when: Before photo of the bare edge; After photo of planted staked trees with GPS and date; Species and count list

Where

public grounds in Hemet, CA

Pay

$360 proposed

This packet is not funded yet, so this figure is a proposed price and not money waiting in escrow. If a buyer funds it, approved proof settles that price onchain. If nobody funds it, approved proof earns provable credit toward the work instead of cash. You see which before you claim, never after.

Proof

Before-and-after photos of the planted, staked parking-edge row

This is exactly what gets it approved. Nothing settles without it.

Level

intermediate

Open until

2026-09-14

How this work is done

A documented method, so this packet comes out the same whoever does it. Typically 45–90 minutes. Method of record: ANSI A300 Part 6 (Planting) + ISA Best Management Practices for tree planting & establishment; Arbor Day Foundation planting standard. DIY-safe volunteer planting on cleared, utility-marked ground; no mechanized or utility-conflict digging.

Bring

• GPS-capable phone
• camera
• round-point shovel + digging fork
• hand pruners
• mulch (wood chips) + measuring stick
• watering can or hose
• gloves + closed-toe boots

Steps

1. 1. Confirm the planting spot is inside the posting radius and clear of marked utilities (811 locate honored); record the GPS waypoint.
2. 2. Photograph the bare site and the nursery stock (label/species visible) before planting.
3. 3. Dig the hole 2-3x the root-ball width and no deeper than the root ball, so the root flare will sit at or just above grade.
4. 4. Remove the container or cut away burlap/wire, gently loosen circling roots, and set the tree with the root flare visible at grade.
5. 5. Backfill with the native soil in layers, firming out air pockets; do not bury the root flare or amend heavily.
6. 6. Build a shallow watering basin, water in slowly until the backfill is saturated, and apply 2-3 inches of mulch kept 3 inches off the trunk.
7. 7. Stake only if the tree cannot stand on its own; use two loose ties that allow trunk movement, and note a removal date within one year.
8. 8. Record species, GPS, before/after photos, root-flare-at-grade confirmation, mulch depth, and water applied into the proof record; sign.

If it does not match the plan

• Unmarked or suspected buried utility, or the 811 locate is not honored -> STOP: do not dig; reschedule after a confirmed locate.
• Root ball is dry, circling/kinked, or the trunk is wounded -> do not plant as-is; soak/correct or reject the stock and note it, rather than establish a failing tree.
• Right-of-way, overhead-line conflict, or a species/site mismatch -> flag for the site steward and choose an approved spot/species; never plant into a conflict.

What counts as done

• GPS waypoint recorded inside the posting radius on utility-cleared ground
• Before and after photos showing the root flare visible at grade
• Mulch applied 2-3 inches deep and held off the trunk, with a watering basin formed and watered in
• Species and any staking (with a removal date) recorded in the proof

Proof is measured against these, not judged by taste.