Install low flow fixtures at a resident's own home, home 3, resident homes in Presidio, TX 79845, Presidio County (own home)

This home still runs standard flow faucet aerators and showerheads, driving up the household's water bill for no benefit over a WaterSense rated swap in this Presidio County community. Standard: EPA WaterSense fixture flow rate and leak audit plus drip irrigation retrofit practice, SDG 6.4 water use efficiency, applied here to household water use in Presidio, TX, Presidio County. Proof: homeowner or resident permission record plus before after photos plus flow rate measurement plus WaterSense label photo plus GPS Reference method for the water_efficiency standard (EPA WaterSense fixture flow-rate + leak audit, ~45-90 min): 1. Confirm the address; get a staff escort; photograph each fixture group. 2. Measure flow rate at each faucet/shower with the bag-and-timer method; record gallons per minute (gpm). 3. Test each toilet for leaks with a dye tablet (wait 10 min, check for color in the bowl); record flush volume. 4. Inspect fixtures, meters, and irrigation for visible leaks/drips; note each. 5. Read the water meter with all fixtures off; note any movement (indicates a hidden leak). 6. Rank WaterSense fixture upgrades + leak repairs by estimated water/cost savings. 7. Record flow rates, leak results, meter check, ranked measures, and photos into the proof record; sign. Equipment: flow-rate measurement bag + timer, toilet dye tablets, moisture meter, GPS / address, camera, tablet / data sheet Done when: Written or recorded permission from the resident; Before photo of each existing fixture; WaterSense rated replacement label or model photo; After photo of each installed fixture with a flow rate measurement confirming the WaterSense maximum

Where

resident homes in Presidio, TX 79845, Presidio County (own home)

Pay

$85 proposed

This packet is not funded yet, so this figure is a proposed price and not money waiting in escrow. If a buyer funds it, approved proof settles that price onchain. If nobody funds it, approved proof earns provable credit toward the work instead of cash. You see which before you claim, never after.

Proof

homeowner or resident permission record plus before after photos plus flow rate measurement plus WaterSense label photo plus GPS

This is exactly what gets it approved. Nothing settles without it.

Level

entry

Open until

2026-08-30

How this work is done

A documented method, so this packet comes out the same whoever does it. Typically 45–90 minutes. Method of record: EPA WaterSense fixture flow-rate + leak audit

Bring

• flow-rate measurement bag + timer
• toilet dye tablets
• moisture meter
• GPS / address
• camera
• tablet / data sheet

Steps

1. 1. Confirm the address; get a staff escort; photograph each fixture group.
2. 2. Measure flow rate at each faucet/shower with the bag-and-timer method; record gallons per minute (gpm).
3. 3. Test each toilet for leaks with a dye tablet (wait 10 min, check for color in the bowl); record flush volume.
4. 4. Inspect fixtures, meters, and irrigation for visible leaks/drips; note each.
5. 5. Read the water meter with all fixtures off; note any movement (indicates a hidden leak).
6. 6. Rank WaterSense fixture upgrades + leak repairs by estimated water/cost savings.
7. 7. Record flow rates, leak results, meter check, ranked measures, and photos into the proof record; sign.

If it does not match the plan

• Meter moving with all fixtures off AND active water damage (wet drywall, ceiling stain, pooling near electrical) -> STOP: possible electrical exposure; keep clear, route to a licensed plumber (and electrician if water contacts wiring). The agent documents, never opens walls.
• Suspected cross-connection / backflow risk (hose-bib, irrigation, boiler makeup) -> flag for a licensed plumber backflow test; potable-water contamination is a health hazard — do not test-operate the connection.
• Toilet dye migrates into the bowl -> flag a leaking flapper/valve for repair.
• Meter moves with all fixtures off -> flag a hidden leak for investigation.
• Faucet > 2.2 gpm or showerhead > 2.0 gpm -> recommend a WaterSense upgrade.
• No electrical/gas work; documentation only — flag suspected pipe damage, do not disassemble.

What counts as done

• Flow rate (gpm) recorded per fixture
• Toilet leak result + flush volume recorded per toilet
• Meter-with-all-off check recorded
• Ranked upgrade/repair measures + photos + address confirm

Proof is measured against these, not judged by taste.