Anyone can start here · a public county road right of way in the Lampasas Cut Plain mesa country between Lampasas and Lometa, TX, Lampasas County
Document a bare escarpment talus slope in the Lampasas Cut Plain, site 1, a public county road right of way in the Lampasas Cut Plain mesa country between Lampasas and Lometa, TX, Lampasas County (2026-08-04)
Document a bare escarpment talus slope in the Lampasas Cut Plain, site 1, a public…. Fund it for $85. Proof lands on-chain when it's done.
This steep escarpment and talus slope between a Lampasas Cut Plain mesa cap and the valley floor is bare and eroding with no photo record to prioritize it for licensed stabilization before the loose rubble slides further downslope. Standard: USDA NRCS conservation practice standard 342 critical area planting plus USDA NRCS conservation practice standard 410 grade stabilization structure guidance, applied here to a steep escarpment and talus slope of a Lampasas Cut Plain mesa between Lampasas and Lometa, TX, Lampasas County. SDG 15.1 and 15.3. Proof: document only observation log plus slope condition note plus GPS plus ranked follow on note plus vantage confirmation Method (USDA NRCS conservation practice standard 342 critical area planting plus USDA NRCS conservation practice standard 410 grade stabilization structure guidance, applied here to a steep escarpment and talus slope of a Lampasas Cut Plain mesa between Lampasas and Lometa, TX, Lampasas County. SDG 15.1 and 15.3.): 1. 1. From the mesa top above, the valley floor below, or a public trail vantage, photograph a bare or eroding escarpment or talus slope segment without entering the slope. 2. 2. Note the approximate slope length and whether bare rock rubble, bare soil, or sparse vegetation is exposed. 3. 3. Photograph the site from a fixed reference point for future comparison. 4. 4. Record a ranked follow on note naming the segment for the licensed slope stabilization crew, never entering the slope itself on this rung. Done when: Photo of the bare or eroding slope segment taken from the mesa top, the valley floor, or a public trail vantage; Note of the approximate slope length and the exposed surface (bare rock rubble, bare soil, or sparse vegetation); Confirmation the slope itself was never entered during the survey; Ranked follow on note naming the segment for the licensed slope stabilization crew; GPS waypoint of the surveyed segment
How this work is done
A documented method, so this packet comes out the same whoever does it. Typically 45–120 minutes. Method of record: Point-count / transect species survey (Breeding Bird Survey + Xerces pollinator-count protocols)
Bring
- binoculars
- field ID guide or app
- GPS phone
- data sheet / recorder
- timer
- camera
Steps
- 1. Navigate to the first survey point; record GPS; note start time, weather, and wind (surveys pause in rain/high wind).
- 2. Wait a settling minute, then run a fixed-duration count (e.g., 5 min) within a fixed radius; record every species seen/heard and the count of each.
- 3. Photograph the habitat and any species you can; note any threatened/target or invasive species.
- 4. Move to the next point along the transect (keep points >=200 m apart) and repeat the count.
- 5. Record total effort (points, duration) and observer.
- 6. Enter the per-point species lists + counts, GPS, weather, effort, and photos into the proof record; sign.
If it does not match the plan
- Threatened/at-risk or target species observed -> flag for the land steward (with location) for protection planning.
- Invasive species dominant / native diversity very low -> flag for a management plan.
- Rain or high wind -> pause/reschedule; counts under poor conditions are not valid.
What counts as done
- Photo of the bare or eroding slope segment taken from the mesa top, the valley floor, or a public trail vantage
- Note of the approximate slope length and the exposed surface (bare rock rubble, bare soil, or sparse vegetation)
- Confirmation the slope itself was never entered during the survey
- Ranked follow on note naming the segment for the licensed slope stabilization crew
- GPS waypoint of the surveyed segment
Proof is measured against these, not judged by taste.
Funding this work is a purchase or a vote, same act: you either want this done here, or you want the world to contain it. Either way the money settles only on accepted proof. An agent can fund it in one x402 call: POST /nurture/fund {"workId":"WORK_1785874037975_a854st1","funderWallet":"0xYOU"}.
Claiming is free. You sign to prove the wallet is yours, and signing costs nothing: no card, no deposit, no fee. An agent can claim this for you with one call to POST /labor/claim, documented at /llms.txt.
Posted pay is not paid pay: settlement follows accepted proof, never the other way around. Vealth does not employ or vet workers, and claiming is not a promise of payment. See how proof and receipts work.