检修投放点的洗手龙头，让人投完能洗手：江苏省苏州市苏州工业园区金鸡湖湖滨公共步道 | Service the handwash tap so a person can wash after using the point: Jinji Lake public lakeside walk, Suzhou Industrial Park, Suzhou, Jiangsu.

投放点旁边的洗手龙头是这套设施能不能被人正常使用的关键一环。龙头长期滴漏或者被水垢堵到只剩一线水，居民就不再用它，投放点的卫生也跟着塌下去。换垫圈、清起泡器、拧紧接头，一次到位。现场：江苏省苏州市苏州工业园区金鸡湖湖滨公共步道。环湖公共步道全线开放，夜间人流大，分类投放点与座椅使用强度高。 | English: The handwash tap beside a drop-off point is what makes the whole fixture usable. A tap that drips for months, or that scale has choked to a trickle, stops being used, and the point's hygiene falls with it. New washer, cleaned aerator, tightened connection, done in one visit. Site: Jinji Lake public lakeside walk, Suzhou Industrial Park, Suzhou, Jiangsu. An open lakeside walk with heavy evening use, so its sorting points and benches take constant wear.

Where

Jinji Lake public lakeside walk, Suzhou Industrial Park, Suzhou, CN · Open the map

Pay

$190 proposed

This packet is not funded yet, so this figure is a proposed price and not money waiting in escrow. If a buyer funds it, approved proof settles that price onchain. If nobody funds it, approved proof earns provable credit toward the work instead of cash — recorded, and readable any time at vealth.net/labor/credit/(your wallet). You see which before you claim, never after.

Proof

作业前后照片 + 滴漏频率变化 + 更换部件清单 + 一分钟出水量 | before and after photos + change in drip rate + list of parts replaced + one-minute flow

This is exactly what gets it approved. Nothing settles without it.

Level

intermediate

Open until

2026-11-19

Posted by

0x034F…6c89

The creator wallet. Its signature is what approves proof and settles the wage.

How this work is done

A documented method, so this packet comes out the same whoever does it.

Steps

1. 1. 拍摄作业前照片，记录滴漏频率和出水状况，并与管养单位确认可关闭的角阀位置。 | Photograph the tap as found, record the drip rate and the flow, and confirm with the maintenance unit which isolating valve may be closed.
2. 2. 关闭角阀，拆下龙头起泡器，清除水垢和杂质后装回。 | Close the isolating valve, take off the aerator, clear the scale and grit from it and refit it.
3. 3. 更换磨损的垫圈或阀芯，拧紧接头至不渗，不使用过大扭矩。 | Replace the worn washer or cartridge and tighten the joint until it stops seeping, without over-torquing it.
4. 4. 开阀试水，记录滴漏是否停止和一分钟出水量。 | Open the valve, test, and record whether the drip has stopped and what the tap delivers in one minute.
5. 5. 拍摄作业后照片，登记更换的部件和试水结果。 | Photograph the finished tap and log the parts replaced and the test result.

What counts as done

• 龙头滴漏或出水不畅的作业前照片 | Before photo of the dripping or restricted tap
• 同一龙头检修后的照片 | After photo of the same tap serviced
• 更换部件清单 | List of parts replaced
• 检修前后的滴漏频率与一分钟出水量 | Drip rate before and after and the one-minute flow

Proof is measured against these, not judged by taste.