a NE-2 highway shoulder near Alliance, NE 69301
Repair a snow-drift-control fence panel line, segment 2 -- a NE-2 highway shoulder near Alliance, NE 69301.
A credentialed crew in hi vis gear repairs the broken slats and leaning posts of the snow fence along the highway shoulder at a NE-2 highway shoulder near Alliance, working from behind traffic control until the line stands plumb again. Read all of it
Not funded yet. Settles as earned credit, $600 proposed.
Proof it takes, the deadline, the level
- Proofcounty/state road-department coordination record + before/after photos + post-plumb and slat-spacing measurement + GPS
- Open until2026-11-15
- Leveladvanced
All of it: the words, the place, the proof
Repair a snow-drift-control fence panel line, segment 2 -- a NE-2 highway shoulder near Alliance, NE 69301. This structural snow-fence line along NE-2 has broken slats and leaning posts after a hard Panhandle winter, letting drifting snow build back up across the travel lanes it was built to protect -- repairing the panel line to spec (NDOT/WYDOT living-snow-fence highway-safety program pattern) restores the visibility and drift control that keeps drivers safe through the next storm season.
Fund it for $600. The receipt lands onchain once the proof is approved.
Safety, read before you claim
HAZARD-CLASS, advanced/credentialed crew only: hi-vis PPE, traffic-control cones/signage or a flagger, work only from the shoulder/right-of-way outside the clear zone, stop all work and clear the shoulder immediately if traffic conditions become unsafe. Call 811 before any digging.
How this work is done
How this work is done
A documented method, so this packet comes out the same whoever does it.
Bring
- the 811 utility-locate confirmation + the owner or agency work authorization
- replacement posts, pickets, fabric or fencing per the agency's spec, plus ties and fasteners
- post-hole tool or driver, hand mallet, fence stretcher or tensioning tool
- string line, level, tape measure
- gloves, eye protection and hearing protection where a driver is used
- camera + GPS phone
Steps
- 1. Photograph the fence run as found, and record what failed (leaning or broken posts, cut or slack fabric, a gate that will not latch) with counts.
- 2. Confirm the owner or agency authorization for this run, and confirm the 811 locate is honored and marked before any post hole is opened.
- 3. Set a string line along the intended fence line so the repair follows the original alignment and does not creep onto a neighboring parcel.
- 4. Reset or replace the failed posts to the agency's specified depth, and replace broken pickets or fabric with the specified material.
- 5. Tension the run to the specified tension and rehang or adjust the gate so it swings and latches through its full travel.
- 6. VERIFY: confirm the finished line is plumb and straight against the string, the gate latches, and no sharp wire end or protruding fastener is left in public reach.
- 7. Photograph the repaired run from the before vantage, log the post and picket counts, and enter them in the proof record.
What counts as done
- Coordination record with the county or state road department before any work in the highway right-of-way
- Before photos of the broken slats/leaning posts along the segment
- Post-plumb and slat-spacing measurement after repair, matched to the standard fence-line spec
- After photos confirming the repaired segment stands plumb and intact
Proof is measured against these, not judged by taste.
What is promised, and what is not
Three separate acts, never one: a vote is a free signed preference that moves no money; a pledge is free signed backing intent, balance-checked, that moves no money and never marks the packet funded; funding is a real payment, made by the payer straight to the worker, with no Vealth fee. Paying Vealth is closed: Vealth takes no new card or wallet payment for a job. To fund a job, offer to pay the worker directly, then pay them yourself when you accept the proof, from your own wallet or by your own card or bank. From a wallet: prepare_token_offer, sign, submit_token_offer; after the proof is accepted you pay the worker on chain and the worker records it (prepare_token_settlement, or POST /labor/settle for USDC on Base). By card or bank: prepare_direct_offer, sign, submit_direct_offer; you pay the worker yourself and the worker records it with prepare_direct_settlement. Both are free, need no gas, and move no money through Vealth.
Claiming is free. You sign to prove the wallet is yours: no card, no deposit, no fee. Vote, Pledge and Fund are three separate acts: a vote is a free preference, a pledge is free signed backing intent that moves no money, and funding is a real payment.
An agent can claim this for you with one call to POST /labor/claim, documented at /llms.txt.
Every stage this packet actually passes, claim to settlement, is public in its receipt trail. A stage that has not happened is not claimed.
Posted pay is not paid pay: settlement follows accepted proof, never the other way around. Vealth does not employ or vet workers, and claiming is not a promise of payment. See how proof and receipts work.
Other acts: vote, pledge, fund
Packet WORK_1789587074520_uvjmv0q