the 400 block of E Ninth Street, Tenth Street Historic District, Oak Cliff, Dallas, TX 75203
Repair a broken sidewalk panel with a permeable finish, Tenth Street Historic District (75212) (site C).
A crew wet-cuts and removes a damaged sidewalk panel at the 400 block of E Ninth Street, sets a new permeable surface to grade, and confirms it drains with a water test. Read all of it
Not funded yet. Settles as earned credit, $720 proposed.
Proof it takes, the deadline, the level
- Proofpermit + before/after level readings + infiltration test video + GPS
- Open until2026-10-30
- Leveladvanced
All of it: the words, the place, the proof
Repair a broken sidewalk panel with a permeable finish, Tenth Street Historic District (75212) (site C). Root-heaved, cracked sidewalk panels in the Tenth Street Historic District trip residents daily and shed every drop of rain to the gutter instead of the ground.
Fund it for $720. Proof lands onchain when it's done.
How this work is done
How this work is done
A documented method, so this packet comes out the same whoever does it.
Bring
- right-of-way permit + traffic cones/barricades and signage
- wet-cut saw or grinder with water feed + vacuum (dust control), or paver lift/reset tools
- permeable paving material (permeable pavers/pervious mix) + bedding aggregate + compactor
- 2-ft level / smart level + measuring wheel + camera
Steps
- 1. ASSESS: measure and photograph each displaced/cracked panel (lift height, cross-slope, ponding), mark the repair extent, and confirm the right-of-way permit and utility locates (811) before any cutting.
- 2. Set up cones/barricades and a safe pedestrian detour; keep all work out of the traffic lane.
- 3. Remove or wet-cut the failed section with water-fed dust controls; excavate to the design subbase and correct the root or subgrade cause (root-prune only per the city arborist standard).
- 4. Place open-graded base and the permeable surface (pavers or pervious mix) to ADA/PROWAG slope and lippage limits; compact and edge.
- 5. VERIFY: check cross-slope ≤2% and vertical discontinuity ≤1/4 inch, water-test infiltration, photograph before/after from the same vantage, and close out the permit.
What counts as done
- Before photos with measured lift/slope readings
- Permit + 811 locate references
- After level readings (cross-slope ≤2%, lippage ≤1/4 in) + infiltration water-test video
Proof is measured against these, not judged by taste.
What is promised, and what is not
Three separate acts, never one: a vote is a free signed preference that moves no money; a pledge is free signed backing intent, balance-checked, that moves no money and never marks the packet funded; funding is a real payment that backs the wage. Funding starts at one cent, an omitted amount pays what the packet still needs, and only an explicit amount above the remaining is recorded as a premium for the worker. Money settles only on accepted proof. An agent can fund it in one x402 call: POST /nurture/fund {"workId":"WORK_1790771611905_183vkqx","funderWallet":"0xYOU"}.
Open, but not claimable yet. restricted: permit-required. Regulated or permit-required work cannot be claimed on this rail yet. It stays readable; voting and pledging are free, and funding is separate from claiming.
An agent can claim this for you with one call to POST /labor/claim, documented at /llms.txt.
Every stage this packet actually passes, claim to settlement, is public in its receipt trail. A stage that has not happened is not claimed.
Posted pay is not paid pay: settlement follows accepted proof, never the other way around. Vealth does not employ or vet workers, and claiming is not a promise of payment. See how proof and receipts work.
Other acts: vote, pledge, fund
Packet WORK_1790771611905_183vkqx