Los Angeles City Hall, 200 N Spring St, Los Angeles, CA 90012
Test and replace every smoke and CO detector battery, Los Angeles City Hall.
An escorted worker presses the test button on a smoke and CO detector at Los Angeles City Hall, then replaces the battery in the unit that failed and re-tests it. Read all of it
Not funded yet. Settles as earned credit, $80 proposed.
Proof it takes, the deadline, the level
- ProofPhoto of each detector with test date logged + Test-pass/fail list before replacement + Photo of replaced batteries with packaging + Re-test confirmation list + security check-in and escort record
- Open until2027-11-10
- Levelentry
All of it: the words, the place, the proof
Test and replace every smoke and CO detector battery, Los Angeles City Hall. Smoke and CO detectors at Los Angeles City Hall run silent past their battery life until they chirp or, worse, until they don't. This is the recurring life-safety rung that keeps the building's air-safety devices live. A detector with a dead battery is silent and does not warn anyone. For the payer: - Price: $40 per job, counted in detectors tested and batteries replaced. - Likely payer: The building's owner or manager, paying directly. - No license is needed: testing detectors and replacing their batteries is maintenance, not construction work, so no contractor license applies.
Offer to pay $80. The receipt lands onchain once the proof is approved.
Safety, read before you claim
Start after the crew's safety orientation. Floor and reachable-ladder height only; never disable a detector without immediately replacing it in the same visit; wear slip-resistant closed-toe shoes and light work gloves.
The full safety list for this job:
- Check in with building security or facilities staff for an escort before entering any non-public area of the building.
- Gear, Title 8 sections 3385 and 3384: slip-resistant closed-toe shoes for stepping up to reach ceilings; light work gloves for sharp covers and dust.
- Orientation, section 3203: the crew's injury and illness prevention program orientation comes before any work.
How this work is done
How this work is done
A documented method, so this packet comes out the same whoever does it.
Steps
- Obtain the owner's or manager's written consent for this work at this address before you start (a signed form, an email or a text that names the address and the work). Write who gave it and the date at the top of your proof. With no consent, stop.
- Check in with building security or facilities staff, get an escort before searching for detectors, and record who checked you in.
- Locate every smoke and CO detector in the building and photograph its test-button label and manufacture date.
- Press-test each unit and log which alarmed and which did not.
- Replace the battery in every unit that did not alarm cleanly, using the manufacturer-specified battery type.
- Re-test every replaced unit and flag any detector past its 10-year replacement date for the next rung.
What counts as done
- Photo of each detector with test date logged
- Test-pass/fail list before replacement
- Photo of replaced batteries with packaging
- Re-test confirmation list
- Confirmation of the building security or facilities check-in and escort before entry
- Consent: the owner's or manager's written consent, naming the address and the work, dated before the first photo.
- Sign-off: the owner or manager signs off the finished work in writing. Write who signed and the date, or the date you asked.
- Photos: take the before photo and the after photo from the same point (stand where the first one was taken and match its frame), each with its GPS point and its date and time.
- Count: detectors tested and batteries replaced, written next to the photos.
Proof is measured against these, not judged by taste.
What is promised, and what is not
Three separate acts, never one: a vote is a free signed preference that moves no money; a pledge is free signed backing intent, balance-checked, that moves no money and never marks the packet funded; funding is a real payment, made by the payer straight to the worker, with no Vealth fee. Paying Vealth is closed: Vealth takes no new card or wallet payment for a job. To fund a job, offer to pay the worker directly, then pay them yourself when you accept the proof, from your own wallet or by your own card or bank. From a wallet: prepare_token_offer, sign, submit_token_offer; after the proof is accepted you pay the worker on chain and the worker records it (prepare_token_settlement, or POST /labor/settle for USDC on Base). By card or bank: prepare_direct_offer, sign, submit_direct_offer; you pay the worker yourself and the worker records it with prepare_direct_settlement. Both are free, need no gas, and move no money through Vealth.
Claiming is free. You sign to prove the wallet is yours: no card, no deposit, no fee. Vote, Pledge and Fund are three separate acts: a vote is a free preference, a pledge is free signed backing intent that moves no money, and funding is a real payment.
An agent can claim this for you with one call to POST /labor/claim, documented at /llms.txt.
Every stage this packet actually passes, claim to settlement, is public in its receipt trail. A stage that has not happened is not claimed.
Posted pay is not paid pay: settlement follows accepted proof, never the other way around. Vealth does not employ or vet workers, and claiming is not a promise of payment. See how proof and receipts work.
Other acts: vote, pledge, fund
Packet WORK_1794290453603_lfno7pj