Swap the corridor storefront lighting to LED.

Replace the fluorescent and incandescent fixtures with LED at the Tweedy Blvd corridor buildings, South Gate, CA. Its ground-floor storefronts burn them every open retail hour, and the swap cuts that load immediately and improves the light quality along the block. The storefront fixtures along the corridor still run old fluorescent tubes every open hour.

Offer to pay $400. The receipt lands onchain once the proof is approved.

What it looks like

At the Tweedy Blvd corridor buildings, a worker on a rated ladder with a spotter pulls the old fluorescent tube from a powered-off storefront fixture and installs an LED lamp, which then lights it.

A description of this kind of work, not a record that it happened here.

Where

the Tweedy Blvd corridor buildings, South Gate, CA 90280. Open the map

Pay

$400 proposed

This job is not funded yet, so this figure is a proposed price, not money held for the worker. If a buyer funds it, approved proof settles that price onchain. If nobody funds it, approved proof earns provable credit toward the work instead of cash: recorded, and readable any time at vealth.net/labor/credit/(your wallet). You see which before you claim, never after.

Proof

before/after photos per fixture + lumen/wattage label photo + fixture count + GPS

This is exactly what gets it approved. Nothing settles without it.

Level

intermediate

Open until

2026-12-10

Posted by

0x034F…6c89

The creator wallet. Its signature is what approves proof and settles the wage.

Start after the crew's safety orientation. Switch the fixture off and test the socket dead before touching it, and use a ladder only after ladder training, never on the top two steps. STOP at scorched, cracked or cloth-covered wiring, any exit or emergency light, and any ballast bypass or rewire, which is licensed electrician work. Never put old fluorescent tubes in the trash; wear electrical-hazard-rated boots and cut-resistant gloves.

The full safety list for this job:

• Power off the fixture at the switch/breaker before changing a hardwired lamp; never work a storefront fixture without a properly rated ladder and a spotter.
• Business-owner consent + scheduling outside open hours precedes work.
• Use a non-contact voltage tester for the dead test. Keep three points of contact on the ladder and never set it across a hallway or exit. Never put a broken fluorescent tube or CFL in the trash. Fluorescent tubes and CFLs hold mercury: do not break them; if one breaks, ventilate for 15 minutes, wet-wipe the pieces, and do not vacuum. Old tubes and CFLs are boxed by type, labeled universal waste with the date, and delivered to an authorized collection point; ballasts marked PCB or leaking oil are not handled by this crew and go to the owner. LED tubes come in three kinds: plug-and-play (works on the existing ballast, allowed), ballast bypass (line voltage at the lamp holders, electrician only, and the fixture is labeled) and external driver (electrician only). Check the lamp label for enclosed-fixture and dimmer ratings and never exceed the fixture's wattage label. Removed halogen and incandescent lamps are hot. Old fixtures with brittle insulation or a burned socket are reported, not worked.
• First-day orientation: this site's hazards, who to call, where first aid is (Title 8 sections 3203 and 1509).
• Fully open and locked stepladder on level ground, never the top two steps, fiberglass near electrical, a second person at the base in a public hallway, never block an exit route (Title 8 sections 3276 and 1675).
• A wall switch off is not lockout: on old or reversed wiring the socket shell can stay live; test with a non-contact tester, and for anything past a lamp the breaker is off, tagged and tested dead (Title 8 Electrical Safety Orders).
• Labels and safety data sheets for lamps, ballasts and any sealant; mercury in tubes and CFLs, PCBs in old ballasts (Title 8 section 5194).
• Glasses on when removing lamps overhead, gloves for hot lamps and broken glass (Title 8 sections 3382 and 3384).
• Footwear, Title 8 section 3385: electrical-hazard-rated boots for electrical hazards and stepping up to reach fixtures.

Three separate acts, never one: a vote is a free signed preference that moves no money; a pledge is free signed backing intent, balance-checked, that moves no money and never marks the packet funded; funding is a real payment, made by the payer straight to the worker, with no Vealth fee. Paying Vealth is closed: Vealth takes no new card or wallet payment for a job. To fund a job, offer to pay the worker directly, then pay them yourself when you accept the proof, from your own wallet or by your own card or bank. From a wallet: prepare_token_offer, sign, submit_token_offer; after the proof is accepted you pay the worker on chain and the worker records it (prepare_token_settlement, or POST /labor/settle for USDC on Base). By card or bank: prepare_direct_offer, sign, submit_direct_offer; you pay the worker yourself and the worker records it with prepare_direct_settlement. Both are free, need no gas, and move no money through Vealth.

Claiming is free. You sign to prove the wallet is yours: no card, no deposit, no fee. Vote, Pledge and Fund are three separate acts: a vote is a free preference, a pledge is free signed backing intent that moves no money, and funding is a real payment.

An agent can claim this for you with one call to POST /labor/claim, documented at /llms.txt.

Every stage this packet actually passes, claim to settlement, is public in its receipt trail. A stage that has not happened is not claimed.

Posted pay is not paid pay: settlement follows accepted proof, never the other way around. Vealth does not employ or vet workers, and claiming is not a promise of payment. See how proof and receipts work.